Analysis and Design Prestress Segmental Crosshead to BS 5400

MIDAS Expert Webinar 18th May 2021 (Tue)

12:00 - 01:00 PM (Malaysia)
12:00 - 01:00 PM (Singapore)

Click here to see it in your local time
EVENT OPENED Register now
OPENED
Analysis and Design Prestress Segmental Crosshead to BS 5400 MIDAS Expert Webinar 18th May 2021 (Tue)

12:00 - 01:00 PM (Malaysia)
12:00 - 01:00 PM (Singapore)

Click here to see it in your local time
OVERVIEW

The basic structural materials for posttensioned segmental crosshead are very similar to posttensioned structures in general, which consist of high-strength concrete, high-strength prestressing steels, and ordinary reinforcing steel, including grout in the duct. The general principle with prestressed design is to ensure that the concrete is either in compression or within accpetable stress limits under service load conditions. Prestress also enhances the shear and ultimate capacity of concrete section.

 

This webinar describes different aspects are considered during the design of segmental crosshead. The procedure will include segmental pier analysis with the particular requirements of the BS 5400.

AGENDA
  • 5 mins

    Introduction of the session

  • 30 mins

    Concepts of Segmental Crosshead Pier Design

    - Demands of Construction Site
    - Key Elements of Crosshead Pier
    - BS 5400 Design Requirements

  • 20 mins

    Application using midas Civil

    - Modelling procedures and parameters
    - Compliance with the code requirements

  • 12:00 - 14:00 SESSION 2-1

    3D Excavation and Piled-Raft Foundation

    [Part 1] 3D Geometry modeling and Meshing
    [Part 2] Analysis control and checking results.

  • 12:00 - 14:00 SESSION 2-1

    3D Excavation and Piled-Raft Foundation

    [Part 1] 3D Geometry modeling and Meshing
    [Part 2] Analysis control and checking results.

  • 12:00 - 14:00 SESSION 2-1

    3D Excavation and Piled-Raft Foundation

    [Part 1] 3D Geometry modeling and Meshing
    [Part 2] Analysis control and checking results.

  • 12:00 - 14:00 SESSION 2-1

    3D Excavation and Piled-Raft Foundation

    [Part 1] 3D Geometry modeling and Meshing
    [Part 2] Analysis control and checking results.

  • 12:00 - 14:00 SESSION 2-1

    3D Excavation and Piled-Raft Foundation

    [Part 1] 3D Geometry modeling and Meshing
    [Part 2] Analysis control and checking results.

  • 12:00 - 14:00 SESSION 2-1

    3D Excavation and Piled-Raft Foundation

    [Part 1] 3D Geometry modeling and Meshing
    [Part 2] Analysis control and checking results.

KEY POINTS

Key point 1: Segmental Crosshead Pier Design Elements

Segmental Crosshead Pier designs are widely used over the years, in response to the demands of construction sites. Each project is different; it has its own demands related to the aesthetics, economy, buildability and safety. The webinar will highlight the key elements influenced the design.

 

Key point 2: Loading Requirements

We will look into the critical loading to be considered in the segmental crosshead design.

 

Key point 3: BS 5400 Design Requirements

midas Civil is a comprehensive package of analysis and design that will be utilized in this project that in compliance with the code requirements.

SPEAKER
  • Sanusi Muda

    Bridge Engineer | MASA Engineering Consultant

    -27 years design experience with extensive experience in bridge
    - Specialization in bridge design
    Participated in major bridge projects in Malaysia
    - SUKE, Kuala Lumpur
    - DASH, Kuala Lumpur
    - TRX, Kuala Lumpur
  • Sanusi Muda

    Bridge Engineer | MASA Engineering Consultant

    -27 years design experience with extensive experience in bridge
    - Specialization in bridge design
    Participated in major bridge projects in Malaysia
    - SUKE, Kuala Lumpur
    - DASH, Kuala Lumpur
    - TRX, Kuala Lumpur
Read all
REGISTER The event is done.
Thank you for your interest.
REGISTER You are registered.

Thanks for registration.
The registration confirmation email has been sent to your email

REGISTER You are registered.

Thanks for registration.
Please check the confirmation email from GoToWebinar for joining the session.

INFORMATION
Event
Analysis and Design Prestress Segmental Crosshead to BS 5400
Session
May 18 (Tue), 2021, 12:00 - 01:00 PM (Malaysia)
May 18 (Tue), 2021, 12:00 - 01:00 PM (Singapore)

Click here to see it in your local time
Date & Location
Date & Location
Document
Notice

1. Participation of this seminar is FREE.
2. We recommend you to register immediately since the number of seats are limited.
3. If you come early to the seminar place, you can enjoy the welcome snack and coffee/tea.
4. For effective training session, we recommend you to bring your personnel laptop computer in order to get the hands-on experience of MIDAS software.
5. Training license and installation guide will be provided to all registrants before the seminar in advance.